Septiembre 2018
 << < > >>


¿Quién está en línea?

Miembro: 0
Visitantes: 2

rss Sindicación



ikea kitchen design

ikea installers

Kitchen Cupboard Set up - Step-By-Step Guidance on how to Install Kitchen Cupboards On your own

Given that you have got your new kitchen cupboards, you might be all set to move on towards the subsequent major phase.....Putting in your kitchen area cabinets. Whilst the actual installation from the Kitchen area Cupboards isn'tall that onerous, the crucial initial move is measuring and marking out where the cabinets will go. By placing layout markings on the partitions and flooring, it will don't just assist you to with kitchen cabinet placement and stud locations, but it will even assist you to identify where by changes and shims will likely be needed. Before we get rolling you'll find a couple of items that you will need for your task:


Degree or Laser Level


Tape Evaluate

Stud Finder


1" x 3" Piece of lumber (6'-8' in length) or an Inverted U-shaped body (see notes under)


Screws (long plenty of to go one 1/2 into your studs)

Utility knife or chisel

Marking Compass

An additional established of fingers (it's possible you'll really need to bribe just one of one's close friends)

As I discussed higher than, you have got the choice of using a bit of 1' x 3' lumber for your installation or building a frame to assist the cupboards (I've provided a picture of a sample body below). This may be made out of 2' x 4's and may be tall enough to support the underside of your respective wall cabinets. When you program on installing multiple kitchen area, then I'd personally counsel the body, but a chunk of lumber will just do wonderful if this is the 1 time celebration. In both scenario, you are going to need yet another established of hands to assist along with the set up.

In cases like this we purchased (RTA) Ready-To-Assemble Kitchen area Cupboards from RTA Kitchen & Bathroom Cabinet Store. Now the kitchen area cabinets are assembled, we are completely ready to start marking out our structure lines. Some people start while using the base cupboards, but we are going to start along with the wall cupboards 1st. There is no right or wrong way to start, I just prefer to start with all the upper cupboards first.

1. Use a amount and a pencil to draw a parallel line across the wall about three inches up from the floor. Evaluate down from this line, on the floor, and find the floors high point (if it has just one), and mark a line at that point. From that high point, Evaluate up 34 1/2 inches and draw a level line across the wall to designate the top of your base cabinets.

two. Since you may have the top in the base cabinets marked, measure up a different 19 1/2 inches and a amount line across the wall to indicate the bottom with the wall cupboards. Lightly mark each cabinets' dimensions and placement on the wall to make sure that your original structure is correct.

3. Use a stud finder to identify the wall studs. Use a pencil to mark the stud areas at least 6 inches higher than and beneath the line for the bottom on the wall cabinets. Draw straight vertical lines between the top and base marks to indicate the center in the studs.

4. When you decided to go using the piece of 1' x 3' lumber, now is wherever you'll use (in the event you decided to go with the U-shaped frame, it can come into play after all your lines are laid out). Screw a temporary 1' x 3' guidance rail for the wall, aligning the top edge of the rail while using the line for your base edge of the wall cabinets. Attach it by driving three or 4 two inch screws through the rail into the wall studs.

5. Given that we have all the lines marked, it is time to start setting up your kitchen area cabinets. We are going to start while using the corner cabinet (here is in which your helper's excess established of fingers are going to be needed). Place the corner cabinet onto the temporary assistance rail and have your helper hold the corner cabinet in place. Drill pilot holes through the sturdy cabinet back or its aid rail and in to the wall studs. Screw the cupboard into your wall making use of two screws that are lengthy plenty of to penetrate the studs by at least one 1/2 inches. Check the top in the cupboard for level and the front from the cupboard for plumb. If you really have to correct the position, just back the screws out a little bit and top shims behind the cupboard at the stud destinations. If it is plumb and amount, drive the screws all the way in and add several a lot more into each stud to ensure that the cabinet is secured tightly to your wall.

6. Now we are going to move onto the cabinets on both side of the corner cupboard. As you set up each 1, use the clamps to secure each cabinet on the neighboring cupboard and then check it for plumb with your amount. On faceframe cupboards, it is really a good idea to drill two 1/8 inch pilot holes through the sides of your faceframe and use screws. In this instance, with frameless, ready-to-assemble kitchen area cupboards we are going to screw through the plywood sides and use shims in between the cabinets to ensure a tight fit and make sure that the cupboard faces are plumb.

7. After all the wall cabinets are in place, install the corner or end base case cupboard. Use shims exactly where needed to level the cupboard and raise it up towards the line which indicates the high point of your floor. Be sure it is level from front to back and from side to side, then screw it towards the wall studs. In case you don't have a diagonal corner cupboard or blind base cupboard in the corner, push the adjoining cabinet into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers plenty of clearance to open and close properly. If necessary, tap shims under the cupboard and behind it to adjust for plumb and amount.

8. Drive screws through the cabinet back (and shims) in the wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cabinets with this manner, joining them the same way you connected the wall cupboards in stage 6.

9. If your cupboards end up butting against one more wall, you could possibly need to have a filler strip to make up the last few inches. In the event you have custom cupboards, they must have been built to fill this gap, but in case you are applying stock or RTA Kitchen area Cabinets the filler strip might be needed. For those who do need to use a filler strip, leave the last cabinet detached from the other cupboards. Clamp a straightedge towards the face with the nearest installed unit, extending far adequate for you to put alignment marks over the end wall. Allow a 3/4" offset behind those marks (to the thickness with the filler piece) and fasten a cleat on the wall. Then install and fasten the last cupboard and evaluate the gap between its face body and the wall.

If the wall is flat, simply rip the filler board into the necessary width and fasten it in place. If the wall is irregular, you'll must scribe-fit the filler board. Start by setting a marking compass towards the width in the gap, then place a strip of 1"-wide masking tape along the filler board in the area where by it needs to be trimmed. Clamp the board into the end cabinet's face body, then trace the wall contour using the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face body to the edge with the filler board. Screw or nail the other side for the cleat.

At this point, your kitchen cabinet set up is complete. If you purchased matching crown molding or any other details, these ought to be easily installed now. Depending on whether you had to use shims under the base cabinets, it's possible you'll really need to put in some trim pieces by the toe kicks to cover up the shims or any gaps at the bottom in the kitchen cupboards.

I hope this helps make your kitchen cabinet installation as smooth as possible. When you require any help with cabinet selection, kitchen area structure tips, or ideas for cupboard styles, check out RTA Kitchen area & Bathroom Cupboard Store.

Admin · 49 vistas · Escribir un comentario

Vínculo permanente hacia el artículo completo


Este artículo no tiene Comentario por el momento .....

Escribir un comentario

Estatuto de los nuevos comentarios: Publicado

Se mostrará tu URL

Por favor introduce el código contenido en las imágenes.

Texto del comentario

   (Salvar el nombre, el mail y la URL en los cookies)